How To Snake A Drain Toilet

Because of its design, it’s able to more effectively remove clogs compared to a regular toilet snake (for more on that, keep reading below). The use of a pipe snake machine on a smaller drain line such as a sink drain will require removal of the trap system below the sink.

The Best Drain Snake Complete Buyer's Guide Drain

This means that you can try loosening up the debris so the powered snake won’t be doing much pushing.

How to snake a drain toilet. A thicker cable is needed to clean out the whole pipe. The sink trap could be blocked, but if cleaning it out does not resolve the issue, then it's time to insert the drain snake. Simple clogs consisting of hair and grease can usually be dislodged with a manual drain snake.

A snake is a simple flexible coil, but when manipulated in unnatural directions (like that of a toilet drain) undue tension will be placed on the coil. To begin using your snake, put on your rubber gloves, unwind 3 to 4 feet of cable from the winding spindle, and place the snake head into the opening at the bottom of the toilet bowl. Let the head of the drain snake snag on the obstruction, or continue pushing forward to dislodge the clog.

Don't use excessive force to get it in, or you could damage the device and the drain. This cannot be performed through the toilet as it will scratch the surface of the porcelain and would be very difficult to work the snake through the porcelain trap built into the toilet fixture. The best toilet augers feature a vinyl coating over the cable.

Crank the handle clockwise to send the cable into the drain until the cable has made it completely through. This may take a few minutes. Toilet augers and electric drain snakes are built to conquer 2 different types of clogs in 2 different types of pipes.

Wiggle it back and forth and ease it in. Insert the snake into the drain, sliding in the cable until it meets resistance; Every bathroom should be outfitted with a plunger, but sometimes a plunger isn’t enough.

Instead, you should take the drain trap apart beneath the sink, then insert the drain snake into the horizontal branch drain. Next, turn the crank handle clockwise, which will extend the snake further into the pipes. Pull the drain snake out slowly and carefully.

Unwind the triangular part of your hanger, but leave the hook on the end in place. Set the end of the toilet snake’s metal cable into the bowl, all the way down into the drain. You don't need a lot of pressure, just enough to keep it from turning.

Main line sewer clogs can take hours to snake, depending on the length and number of pipes affected. This usually means it has hit a bend in the pipe but also could be the clog itself. Insert your drain snake slowly insert the auger into the drain.

The gel even cuts through standing water to get your pipes flowing quickly again. Turn the crank clockwise to release the cable steadily, applying slight downward pressure. Keep turning the crank until it stops—you’ve reached the clog.

Manually feed the head of the snake into the pipe, slowly lowering it 8 to 12 inches into the pipe at a time, then spin the handle clockwise. Snaking a toilet with a drain snake. Water in the toilet bowl will help flush away any pieces that end up breaking loose from the clog, so if there isn’t any water, pour some in before you continue and do not flush.

Feed the snake until it reaches the obstruction. Clogs that are deep within your plumbing system are usually easier for you to clear with a power drain snake. Toilet auger vs an electric snake.

Also known as a water closet auger or plumbing snake, this device is designed to move through the drain of the toilet to remove the clog or obstruction that’s causing the stoppage. Turn the manual crank or turn on the motor (if you are using an electric one) to feed the snake into the drain. Turn the handle clockwise to extend the auger's cable (or snake) down into the drain towards your clog.

Guide the head of the snake to the base of the toilet bowl, angled toward the drain. Feed this down your toilet and once your hit resistance, pull back. How to get a drain snake through an elbow or corner in your drain pipe requires a bit of elbow grease.

To snake a toilet, start by placing the curved hook end of the snake into the toilet and feeding it into the mouth of the drain to break up and grab any debris. This winding motion with your drain auger helps it to make its way through corners in your pipes. The most common item recommended to create a homemade toilet snake is a wire clothes hanger.

Place the end of the auger into the toilet bowl so that it points down the drain. Make sure when you wind your drain snake into the pipe that you are rotating it the whole time. Main line sewer clogs can take hours to snake, depending on the length and number of pipes affected.

The head of the auger serves to loosen the clog and/or push the blockage further down the drain, or to pull the blockage up and out of the toilet. If necessary, adjust the angle of entry. With the tip of the snake at the source of the clog, slowly twist the end into the blockage.

And when it can twist no more, attempt to pull out the offending item. Step 3 pull back slightly on the snake. The drain snake you use depends on the complexity of the job at hand.

Rotate the handle at a steady pace. Connect your snake to a power source and insert the head into the toilet drain to begin the process of unclogging. How to snake a toilet with a hanger.

Crank the handle clockwise to release and extend the cable down into the drain; The vinyl coating will help protect the bowl against scratches and marks as you work. Tighten the setscrew to clamp down on the cable;

Plumbers take about five minutes to snake a drain for clogs located near the tub, toilet, or sink. Clean the drain snake and throw away the debris that you pull out. Toilet augers are built with a thicker cable because toilet pipes are usually 4 inches wide.

The hook should grab onto your clog and help loosen it.

Bathtub Drain Stopper Stuck In Open Position Bathtub