How To Build A Eastern Bluebird House

Smooth the edges of the hole with sandpaper Make sure it is mounted 5 to 10 feet off the ground.

Handmade Bird House, Eastern Bluebird (With images) Idei

Peterson bluebird house reprinted with permission from carrol henderson, woodworking for wildlife 01992 minnesota department of natural resources 90' 3/' 3 10 1/4 nail point.

How to build a eastern bluebird house. Round off the edges with sandpaper, or use a round over bit to create a finished edge. For mountain bluebirds), then use a rasp to even out the edges. A clamp in not necessary, but can be helpful for keeping edges straight during assembly.

Side side view outer 21/' g 3/4 both of these edges are to 11/2 In the northern part of their range, mountain bluebirds are known to lay larger but fewer clutches than eastern or western bluebirds. Make a 4″ by 4″ floor (inside dimensions) and 9″ floor to ceiling height (inside front).

The hole should be 1 1/2 inches/3.8 centimeters in diameter for eastern and western bluebirds, though mountain bluebirds occasionally prefer slightly larger holes that are 1 9/16 inches/4.0 centimeters in diameter. Cut the board to the measurements above and drill the 11⁄2” entrance hole using the spade bit. 1.5 inches (1.56 inches for mountain bluebirds) entrance height:

6 to 10 inches above the house floor. Just like the slot bluebird house, it has a hatch door to access the bird and the nest if there is a need. The difference is that starlings usually have the nest cup located farther back in the box than bluebirds, and starlings will include feathers, cloth, string, and even pieces of trash in their nest materials.

Examples would be meadows with short grasses and shrubs, orchards or even your backyard lawn if it is large enough or has a good ratio of open space to trees and/or shrubs. Drill a 1 1/2″ diameter entrance hole located 7″ above the floor (to top of hole). Each bluebird house has six pieces you will need to cut (from smallest to largest):

First clutches average five to six eggs; These screws act as the hinge. Boxes should be placed at (human) eye level for easy access by bluebirds and the people who care for them.

The entrance size is the most critical dimension for a safe, effective bluebird house. Insert the nail to hold the side door closed. Screw the walls, floor, and roof together, leaving one of the side walls unattached.

This house is a simple and inexpensive project to build and can be made from pine, cedar, or redwood boards that are commonly available at home centers and lumber yards. 8 to 12 inches with the back slightly higher to shed water. Cut the sides, base, back, and roof of the bluebird bird house, to the sizes indicated in the drawings, and assemble them together, as shown in the diagrams, using 16 gauge galvanized finish nails.

Assemble back, sides, roof and bottom using nails. Try not to place the house too close to feeders. Drill a hole on the hinged side 2 inches up from the bottom and 1/2 inch in from the side.

If you want to make it easier, make a reference line going down across the left side, then 3/8 onto the back. Drill at a slight downward angle, going through the front of the house and into the side. The best dimensions for bluebird houses are:

Free plans to build a bluebird house. Drill three holes (two in the front, one in the back) through the front Cut one 1×6 to 4″x4″ for the floor (a).

Plans to build nest boxes for eastern bluebirds (sialia sialis). Although the female eastern bluebird (sialia sialis) builds the nest and incubates the young, the male arrives first and makes the initial site assessment. Then, use a spade bit or hole saw to make an entrance hole in the front piece.

Drill 1/4 holes and cut the corners for drainage. Back should hang about an inch below the bottom. Cut two 1×6’s to 4″x10 3/4″ long for the sides (b).

Cut a 1×6 to 13 1/2″ long for the back (c). This will be the door to clean the house 3. Bluebird houses should be spaced at least 100 yards apart so that mating pairs can maintain their territories without stress.

How to build a bird house, pictures, diagrams, and step by step instructions. Eastern bluebirds typically have two clutches a year, but in warmer climates, three clutches are common. High enough to avoid predators bluebird houses should be mounted 4 to 6 feet above the ground.

Mount the finished bluebird nesting box between 5' to 10' above the ground. Attach the entrance guard on a bias for a visually appealing diamond shape. Second clutches average four to five eggs.

The screw for the left sides that are on the front and the back must be in line with each other, otherwise the left side won't swing. Bluebirds prefer large expanses of short grass with a clear flight path, ideally facing a field. Build the eastern bluebird birdhouse with red cedar, pine, or almost any soft wood.

Sides should be flush with the base of the bluebird house. Place nest boxes in the sunniest, most open area possible, away from your house or deep shade. Measure and cut bluebird house door the next step to build a bluebird house is to cut part d from a 1×4 so the end is 45 degrees, and then reset your saw to cut the piece to final length.

If you only have eastern bluebirds, you can use a 1½ inch hole. The hole needs to be 5½ inches from the bottom of the front board.

Horizontal Bluebird House & Nest Box Bluebird house