How To Make A Pillow Cover With A Flap

Now place the front piece and the back pieces right sides together. Stuff your pillow inside and then hand stitch it closed.

DIY Pillowcase Diy throw pillows, Diy pillow covers, Diy

Such a nice, clean looking finish for the back of this pillow cover!

How to make a pillow cover with a flap. Now, turn the entire pillow case right side out, tucking that extra folded edge towards the inside……and press all the edges flat. This method eliminates the need for a special invisible zipper foot while still giving the pillow back a clean professionally finished look that allows the pillow cover to be removed to launder or change decor with the season. Add 1 inch total to the width and height for seam allowance and cut out the material.

Work it into place, putting your hands inside if need be to get the corners positioned correctly. Insert your cushion into your new cushion cover. My pillow measured 20″ x 14 1/2″.

How to make a pillow case in 5 easy steps. Fold the 4 inch rectangle flap back around to the back so that the ties are coming out of the side. I like the cover tight so i cut the fabric out the same size as the pillow.

Turn right side out, poke out corners, and iron flat. With the “wrong” side facing up, fold 1 short edge by 2/8″ (0.6cm), and fold again by 3/8″ (1cm). To make your own pillow case with a zipper, you’ll need the following:

Then, slide your pillow inside like normal, then pull that extra flap up and over your pillow……and now the pillow is hidden. To make these finished edges: Pillows also make appearances in living rooms, dens, patios and any parts of the house that could use a little comfort and decor.

If you want to make a smaller or larger pillow cover, just use the same measurements, but add or subtract 2″ on each side, for each inch enlarged or reduced. Sew the hem for the flaps. First, measure the pillow that you want to cover.

Start by cutting your drop cloth pieces. On one short edge, fold under 1/4” to the wrong side of the fabric. I began by measuring the pillow i was going to cover.

Pin and sew it down, sewing near the bottom of the flap. Learning how to make an envelope cushion cover is a great project for a beginner sewer. The raw edge will now be hidden.

Open the cuff fabric and lay it right sides up on your cutting table. Pillow cases are often made from a fabric that feels comfortable against the skin, like soft cotton, satin, flannel or a jersey knit fabric.[1] x expert source mia danilowicz master tailor expert interview. Pick out fabric that matches the color scheme in your bedroom, especially your bed covering and sheets.

When you peek inside, you should see that folded over section. Iron your cushion cover before putting in the cushion if it has become wrinkled. In about 10 minutes, you can learn to sew these pillow cases with an envelope closure.

Lay the main fabric wrong side down on top of the cuff fabric and lining up the raw edges. Glue or sew a length of velcro to the underside of the flap and to the pillow case itself where the flat meets the rest of the pillow. Press the cuff fabric and the accent fabric in half lengthwise wrong sides together.

Double hem the left and right edges: Cut the front side of your pillow cover the size of your pillow insert. The pieces should meet when you fold down the flap.

Cut out the back panels of the pillow. To make the envelope closure for the back. (1) rectangle, 20″ x 13″.

Hem 1 short edge on both pieces (see arrows). I decided on an 8″ flap, so the measurement for cutting the throw was 21″ x 37 1/2″. If you are making a larger pillow cover, cut one square piece that is the size of your pillow form+2″ and two pieces that are the width of your pillow form and the height is the size of your pillow form+2″.

The pillow cover is going to wrap around the pillow. Step 1, pick out fabric. Then, turn 3 inches more and fold the fabric.

You will need to squeeze it inside between the overlapping flaps on the back of the cover. Fold under flap edge of each back piece 1/2″ and the again 1/4″ to form a small hem for the flaps. In my experience, this makes the pillow cover to big.

Take the width of the front pillow cover, divide it in half and then add three inches to the total for both panels. Most instructions say to make the cover at least 1” bigger on top and side to allow for a ½” seam allowance. The short edges will overlap and have a finished opening.

So if your insert is 16 inches square, you’ll cut a piece of fabric that is 16 inches on all 4 sides. Repeat this for the other short edge. (you can buy amazing fabric online.here are my 5 favorite online fabric sources.)it’s best to use a home decor fabric because it is a bit thicker and holds its shape nicely.

And fold over the edges of the opening towards the inside of the pillow a 1/2 inch, and iron those flat too. Here’s how to make the covers: Line up the corners, so the top back piece will overlap the bottom piece, as i showed you in the photos above.

Complete easy peasy how to video. The front piece is longer because it includes the inner flap. [3] x expert source mia danilowicz master tailor expert.

As for the pillow cover’s length, get the bolster pillow’s length and add 5 inches. Sew around all four sides of the pillow cover, using a 1/2″ seam allowance. Now toss on the couch, add it to your bed, and place on a window seat.

Fold the left and right edges in, overlapping them by 4 inches (10 cm). (1) square, 20″ x 20″. Plus learn how to calculate the fabric needed for your pillow size.

Iron and pin the fold in place. To make a set of standard pillow cases, you will.step 2, cut the fabric to size. Finally, you want to fold one edge of the width at 3 inches with their wrong sides together.

(1) rectangle, 20″ x 17″. How to make an envelope pillow cover supplies to make a zippered pillow case. Open it and get the edges of the pillow cover length aligned with the wrong sides together.

I wanted to make a simple envelope pillow with a flap on the top with the fringe edge of the throw. They are a perfect resting place for your head and provide vital pops of color. Fold each edge in 1/2 inch (13 mm), press, then fold over again 1/2 inch (13 mm), and press.

How to make a concealed zipper pillow back by creating a flap to cover the zipper. Fold under 1/4” again, so the raw edge is completely tucked inside the fold. Pin and sew around the pillow cover with a 3/8 inch allowance.

Update your old throw pillows with this quick and easy envelope pillow cover tutorial.

DIY Pillowcase Diy pillow covers, Diy pillows, Homemade